• <xmp id="oawmy"><source id="oawmy"></source>
  • <xmp id="oawmy"><source id="oawmy"></source>
  • <bdo id="oawmy"><wbr id="oawmy"></wbr></bdo>
  • <td id="oawmy"></td>
    產品詳細信息 更多+
    玻璃盤360度牙傷光學篩選機

    長按識別二維碼查看詳情

    長按圖片可保存到相冊

    圖片加載中,請稍等 ...
    長按圖片保存/分享
    玻璃盤360度牙傷光學篩選機
    玻璃盤360度牙傷光學篩選機
    瀏覽:
    詳情

    玻璃盤360度牙傷光學篩選機

    Optical screening machine for teeth injury of glass plate in 360 degrees

    HL-05-360-LSLM

    參數規格

    Specifications

    本機臺外觀尺寸:

    2300mm*1200mm*2300mm(**)

    機臺重量:約750KG

    更換規格:約10分鐘

    檢測范圍:

    長度:10-60MM  直徑:5-25mm (可以倒立)

    速度最快可達600/分鐘

    本機臺為檢測螺栓、螺帽一體機

    最多可裝8CCD

    電源:交流單項220V  50HZ

    功率:約3KW

    The appearance size of this machine:

    About 1200mm*1200mm*2300mm (length*width*height)

    Machine weight: about 750KG

    Replacement specification: about 10 min

    examination range:

    Length: 10-60mm Diameter: 5-25mm (can be inverted)

    The fastest speed:600 / min

    This machine is a testing bolt and nut integrated machine

    Up to 8 CCDs

    Power: AC single 220V 50HZ

    Power: about 3KW

    可檢測項目

    Suitable for

    ○外螺紋360度牙傷檢測;○螺紋直徑公差檢測;

    ○最大/最小對邊公差檢測;○有無印記檢測;

    ○螺紋牙底徑檢測;○最大/最小對角公差檢測;

    ○螺紋牙中徑檢測;○內孔與外圓同心度檢測;○牙距檢測;

    ○內孔徑有無毛刺檢測;○有無螺紋檢測;

    ○頭部有無電鍍檢測;○斜牙檢測;○頭部表面開裂;

    ○粗細牙檢測;○內孔直徑公差;○尖銳度檢測;

    ○有無焊點,及焊點數檢測;○頭部真圓度測量;

    ○焊點面積檢測;○搓牙有無到位檢測;○牙數檢測;

    ○螺帽牙內有無鐵屑檢測;○各部位臺階公差檢測;

    ○梅花形狀及有無滾花檢測;○頭部厚度公差檢測;

    ○螺帽爛牙、壞牙檢測(可360度檢測);○總長度公差檢測;

    Thread diameter tolerance detection;Maximum / minimum alignment tolerance detection;Threaded teeth bottom diameter detection; Maximum/minimum diagonal tolerance detection;Thread middle diameter detection; Concentricity detection of inner hole and outer circle; Distance detection between teeth;

    Detection for burr in internal aperture or not; Thread or not;

    Electroplating on head or not; Oblique teeth detection; Head surface cracking;

    Teeth thickness detection; Diameter tolerance of inner hole; Sharpness detection;Detection for solder joint or not and the number;Head roundness measurement;Solder joint area detection;Detection for rub teeth in place or not;Teeth number detection;Detection for iron chip in nut teeth or not; Step tolerance detection of each part;Detection of plum blossoms and annular knurl or not; Head thickness tolerance detection;Detection for broken teeth and bad teeth of nut (360 degree detection);Total length tolerance detection;




    @copyright 2019 華磊(嘉興)智能科技有限公司

    All rights reserved 浙ICP備19042112號-1

    添加微信好友,詳細了解產品
    使用企業微信
    “掃一掃”加入群聊
    復制成功
    添加微信好友,詳細了解產品
    我知道了
    2020狠狠狠狠久久免费观看
  • <xmp id="oawmy"><source id="oawmy"></source>
  • <xmp id="oawmy"><source id="oawmy"></source>
  • <bdo id="oawmy"><wbr id="oawmy"></wbr></bdo>
  • <td id="oawmy"></td>